Kingmaster International Trade (Tianjin) Co.,ltd-京登威国际贸易（天津）有限公司
 



 

京登威国际贸易(天津)有限公司
      
KingMaster International Trade(Tian Jin) CO.,LTD
     
其他汽修工具
other tools

2 JAW GEAR PULLER

2爪齒輪拔

NO. GP2 - 3"
NO. GP2 - 4"
NO. GP2 - 6"
NO. GP2 - 8"
NO. GP2 - 12"


3 JAW GEAR PULLER
3爪齒輪拔
NO. GP3 - 3"
NO. GP3 - 4"
NO. GP3 - 6"
NO. GP3 - 8"
NO. GP3 - 12"
No.GP-234
No.GP-237
2&3 Jaws 2In1 Gear Puller
两爪三爪轴承拔
Drop forged chrome vanadium steel
4"102mm Capacity Range 3"-4"
7"178mm Capacity Range 3"-7"
铬钒钢锻造
4"120毫米适用范围3"－4"
7"178毫米适用范围3"－7"
Operate Instruction:
1.You can operate this product with 3 jaws or 2 jaws pulling.even two different pulling ways:External or Internal models,only need to change or convert jaws sddembling.
2 How to change or convert jaws assembing: please relax the Round screw cap in order to relax the pressure spring, then you can easy to move the jaws from the central cross arm.
3 When you operate this product please make sure all parts are fixes on the right place,even all the accessories without any damage.
4 After operating,please maintain all parts and often to keep all the accessories clean.
操着说明：
1 该工具在可用做内外径拉拔器的同时，还可作为3爪和2爪拉拔器，只需更换拉拔爪手即可.
2 更换拉拔爪手方法：先旋转松懈圆头螺帽，以解弹簧压力，然后可轻易从中央臂上拆除拉拔爪手.
3 操着此工具时，请务必保证所有零部件都被固定在正确的位置，任何零部件不许有任何损坏,
4 使用之后请收好各部件，并保证所有零部件清洁.
NO.KM-6330A
PITMAN ARM PULLER
拉拔器
Maximum opening: 3" (75MM)
Maximum throat dopth: 3.3/8"(85MM)
lenght: 6.3/8"(160MM)
适用于卡车
最大开口：3"（75MM)
最大喉深：3.3/8"（85MM)
长度： 6.3/8"(160MM)
NO.KM-6330
PITMAN ARM PULLER
拉拔器
Maximum opening:2.1/2"(65MM)
Maximum throat dopth: 3.3/8S"(85MM)
lenght:6"(150MM)
适用于小车
最大开口：2.1/2"(65MM)
最大喉深：3.3/8S"(85MM)
长度：6"(150MM)
NO.KM-8082
PITMAN ARM PULLER
拉拔器
Spread:2-5/8" TO 3-3/8"
Reach:2-1/4"
Pressure Screw:3/4"～16x6-11/16
伸展2-5/8"
可达到 3-3/8"
驱动压力 3/4"～16x6-11/16
NO.KM-385
NO.KM-385S

TIE ROD PULLER

球頭取出器(直式)
NO.KM-385 large
NO.KM-385S small
The adjustable jaws specially designed can be connected to the outer tie rod end with one hand.
The tool has the strength to separate those tough worn tie rod ends of any design foreign of domestic.
NO.KM-385 大
NO.KM-385S 小
特殊设计的可调整爪能够连接外部连杆头，一只手即可操作.
该工具适合国内外各种机车，能分离坚固球头.
NO.KM-395

TIE ROD PULLER

球頭取出器(卧式)
Heat treaded drop forged steel body & boil for long rough usage.
Spread ball joint easily where space prevent use of direct action method.
Jaw opening 19mm,maximun opening 38mm.
特殊硬化处理，长久耐用.
在狭小空间可轻松拆卸球头.
爪开口19毫米，最大开口38毫米.
NO.KM-8685
NO.KM-8698
Universal Ball Joint Puller
橫拉桿球頭拔卸器
NO.KM-8685 large
NO.KM-8698 small
For removing the ball pivots on steering arms, steering tie rocks, steering knuckles, etc.
NO.KM-8685 大
NO.KM-8698 小
用于拆装操纵杆上各部位球头型物件.

Tie Rod/Pitman Arm Adjusting Set

连杆臂调节工具组
these tools have a unique design that permits 360 °rotation of the adjusting sleeve,even where space is limited.
Accommodate 1/2"drive ratchet or breaker bar.
该产品设计独特，在较小空间亦可执行调整之功能，可360度旋转。
与1/2“棘轮扳手配套使用
NO.KM-8515
5PC Ball Joint Separator Kit
五件球头取出器组
Three forged steel forks.
Interchangeable shafts for use with ball pein hammer or air hammer.
Suitable for most small cars and light commercials.
Includes: 1pc 11/16" tie rod spreader
　 　 　 　 1pc 15/16" ball joint spreader
　 　 　 　 1pc 1-1/8" pitman arm wedge
　 　 　 　 1pc striking handle
　 　 　 　 1pc air hammer adapter
三个锻造钢叉
可变换轴既适用于打击锤，也适用风动锤.
适用于大多数小型车和小货车
组件：
1件连杆球头取出器
1件球头取出器
1件连杆臂嵌入器
1件打击柄
1件风动锤转接器
NO.KM-2030

BALL JOINT SERVICE KIT

十字軸拆裝器

This heavy duty tool is also a u-joint press and brake anchor pin. Pusher tool.
Used on all cars and light trucks.
Having press-fit type ball joints.
You can remove and install ball joints without removing control arm from the vehicle.
Complete with 5 piece receiver tubes and adapters.
适用于大多速轿车和部分轻卡车
可以安装或取出球头，而不必从机车上取下控制杆
附有五件管和转接头.


ARMATURE BEARING PULLER
軸承拔 鉻釩鋼鍛造

 

CODE NO. AB-1
CODE NO. AB-2
CODE NO. AB-3

 
CODE NO. AB-1 （適合中小型驕車）
CODE NO. AB-2 （適合中大型驕車）
CODE NO. AB-3 （適合大卡車、大貨車）
Bearing Separator
轴承拔
Bearing Separator
轴承拔
NO.YC-506
13 PCS HARMONIC BALANCE PULLER
13件平衡拉拔器
Yoke 1 pc(Drop Forged )
Bolt 1 pc (φ14mm×L 140mm×10t/inch)
Adapter 1 pc
Screw & Nut
2 PCS 3/8"×16nc×4"
3 PCS 3/8"×24nf×3"
3 PCS 5/16"×28nc×2"
3 PCS 8mm×1.25×80mm"
套轭一件
螺钉一件 φ14mm×L 140mm×10t/inch
转接头一件
螺丝头和螺帽
2 件 3/8"×16nc×4"
3 件3/8"×24nf×3"
3 件 5/16"×28nc×2"
3 件 8mm×1.25×80mm"
用于方向盤 法蘭盤
NO.PSP-7001

PRESSURE SCREW SEPARATOR PULLER SET
17件分离式轴承拔组

BEAM 1PC
NUT 4PCS
CENTRAL BOLT 1PC
BEARING SEPARATOR&BOLTS 1 SET 75-105mm
MAIN ROD 2 PCS
EXTENSION ROD 2 PCS
JAW LEG 2 PCS
DEEP ROD 2 PCS

适用 75 － 105mm
组件：
横梁一件，
螺帽四个，
中轴一件，
轴承拉拔器一套,75-105mm
主棒两根，
连接杆两根，
支脚两根。
NO.YC-701

TWO AXLE SLIDE HAMMER SET

錘打式輪鼓拉拔器

"T" Bar 1 Pc
Hammer 1 Pc 从，(5 Lbs. Cast Iron)
Axle Puller 2 Pcs
Grip Wrench Adapter 1 Pc
Nut 1 Pc Two Jaw Head 1 Pc
Three Jaw Head 1 Pc
Screw & Nut 3 Pcs
Attachment 1 Pc
Attachment 1 Pc
Jaw 3 Pcs (Drop Gorged )
Tapping Screw 1 Pc
Hook 1 Pc

组件：
T型杆一件
锤子一个，(5 Lbs. Cast Iron)
轮轴拉拔器两件
扳手转接头一个
螺帽一个，两爪头一个
三爪头一件，
螺丝刀螺帽三件，
爪三个，
自攻螺钉一件，
附属装置一个。
NO.YC-705

14 PCS HYDRAULIC SEPARATOR PULLER SET

14件油壓分離式軸承拔組

Hydraulic Ram 1Pc
(SCM415φ37.7 mm x L160 x 16t)
Bearing Separator & Bots 1 set （150mm 42°-45°)
(SCM415 Drop Forged Hardened 42°- 45°Capacity 150mm)
(Bolt 5/8" x 11nc x L216mmφ6mm SCM415)
Main Rod 2 Pcs
(Hex Bar 21mm x L7"x 5/8"11nc
Extension Rod 2 Pcs
(Hex Bar 21mm x L7"x 5/8"11nc
Beam 1Pc
Adapter 1Pc

適用150mm軸承,操作特別省力適用
液压杆一件 (SCM415φ37.7 mm x L160 x 16t) ，
轴承拉拔器一套 （150mm 42°-45°)
(SCM415 特殊硬化处理 42°- 45°适用 150mm)
(螺栓 5/8" x 11nc x L216mmφ6mm SCM415) ，
主杆两件 (六角杆 21mm x L7"x 5/8"11nc ，
连接棒两件 (六角杆 21mm x L7"x 5/8"11nc ，
横梁一件
转接头一件。
NO.YC-706

TWO SETS BEARING SEPARATOR ASSEMBLY

雙盤組分離式軸承拔組

Bearing Separator & Bots 2 sets
SCM415 Drop Forged Hardened 42°- 45°
Capacity: 30mm-50mm, 50mm-75mm
(Bolt φ3/8" x L216mm x 24t SCM 415 Hardened 42°- 45°)
(Bolt φ1/2" x L135mm x 20t SCM 415 Hardened 42°- 45°)
Main Rod 4 Pcs (Hex Bar 17mm 3/8" x L127mm x 16t) Exetension Rod 4 Pcs
(Hex Bar 14mm 3/8" x L102mm x 16t)
Beam 1Pc
Center Bolt 1 PC (9/16 x L175 x 10 t / inch )

適用30-75mm的軸承
组件：
轴承拉拔器两套，
SCM415 特殊硬化处理 42°- 45°适用: 30mm-50mm, 50mm-75mm
(螺栓 φ3/8" x L216mm x 24t SCM 415 硬化处理 42°- 45°)
(螺栓 φ1/2" x L135mm x 20t SCM 415 硬化处理 42°- 45°)
主棒4根 (六角杆 17mm 3/8" x L127mm x 16t)
连接杆4支 (六角杆 14mm 3/8" x L102mm x 16t)
横梁1根
中轴一根 (9/16 x L175 x 10 t / inch )
NO.YC-707

HYDRAULIC SEPARATOR PULLER SET

油壓分離式軸承拔組

Hydraulic Ram 1 Pc
(SCM415φ37.7mm x L160 x 16t)
Bearing Separator & Bolts 1 Set
(SCM415 Drop Forged Hardened 42°-45°Capacity 75mm-105mm)
(Bolt 5/8" x 18t SCM415 Hardened 42°-45°)
Main Rod 2 Pcs
Extension Rod 2 Pcs 8" x 1.75p
Beam 1 Pc

適用75-105mm軸承操作特別省力
液压杆 一根(SCM415φ37.7mm x L160 x 16t)
一套轴承拉拔器
(SCM415 特殊硬化处理 42°-45°适用 75mm-105mm)
(螺栓 5/8" x 18t SCM415 硬化处理 42°-45°)
两根主棒
连接杆 8" x 1.75p
一副横梁
NO.YC-708

PRESSURE SCREW SEPARAOR PULLER SET

分離式軸承拔組

Beam 1 Pc Central Bolt 1 Pc
(φ18.65mm x L11.5" x 10t)
Nut 1
Bearing Separator & Bolts 1 Set
(SCM415 Drop Forged Hardened 42°-45°Capacity 75mm-105mm)
(Bolt 5/8" x 18t SCM415 Hardened 42°-45°)
Main Rod 2 PCS (8" x 1.75p )
Extension Rod 2 Pcs (8" x 1.75p )

適用75-105mm軸承
组件：
横梁一副，
中轴一副，
螺帽一个，
轴承拉拔器一套，
(SCM415 特殊硬化处理 42°-45°适用 75mm-105mm)
(螺栓 5/8" x 18t SCM415 硬化处理 42°-45°)
主棒两条，(8" x 1.75p )
连接杆两条，(8" x 1.75p )
NO.YC-709

HYDRAULIC GEAR PULLER

23件油壓分離式多功能軸承拔組

Hydraulic Ram 1 Pc
(SCM415φ37.7mm×L1602×16t)
4", 6", 8" Leg each 3 pcs Hardened 42°-45°(SCM415)
Twin Head 1 Pc
Triple Head 1 Pc
Sent Pop 1 pc
Extension Rod 1 pc (1" x 2" )
Extension Rod 1 pc (1" x 4" )
Main Rod 2 pcs (8" x1.75p )
Extension Rod 2 pcs (8" x1.75p )
Beam 1pc
Bearing Separator & Bolts 1 Set
(SCM415 Drop Forged Hardened 42°-45°Capacity 75 mm-105 mm)
(Bolt 5/8" x18t Capacity 105mm SCM 415 Harden 42°- 45°)
Nut 1 pcs (Ram Part SCM415 Hardened 42°- 45°)
Metal Box 1 Pc

適用100, 150, 200mm 齒輪及軸承
有二爪三爪的功能操作特別省力
液压杆一件，
(SCM415φ37.7mm×L1602×16t) ，4", 6", 8"支腿每套3件 硬化处理42°-45°(SCM415)
两个顶梁 ，
三角头一个，
连接头2个，(1" x 2" )， (1" x 4" )
连接杆2根，(8" x1.75p )
主棒两根，(8" x1.75p )
横梁一件，
轴承拉拔器一套，
(SCM415 特殊硬化处理 42°-45°适用 75 mm-105 mm)
(螺栓 5/8" x18t 适用 105mm SCM 415硬化处理 42°- 45°)
螺帽一个。
NO.YC-710

SIX WAYS MULTI pURPOSE HYDRAULIC GEAR PULLER SET

六用齒輪拔組

Hydraulic Ram 1Pc
(SCM 415φ 37.7 mm x L160 x 16t)
Combination Cross Head 1 Pc
Combination Leg
(SCM415 Drop Forged Hardened 42°- 45°)
Steel Plate 6 Pcs
Extension Rod 1Pc(1"x1 1/4" )
Extension Rod 1Pc(1" x 2")
Screw Nut & Washer 6 Pcs

該組齒輪拔含有二爪三爪功能, 適用150, 200, 250mm
组件：
液压杆一件，(SCM 415φ 37.7 mm x L160 x 16t)
复合交叉头一个，
复合支脚，(SCM415 特殊硬化处理 42°- 45°)
钢盘六个，
连接杆两根(1"x1 1/4" )和(1" x 2")
六个驱动头。
NO.YC-900

10 LBS DENT PULLER 10LBS

扳金拉拔器

Pipe 1 Piece (φ22.5mm x L590mm)
Hammer 1 Pc (10 Lbs Cast Iron)
Pipe 1 Pc (φ22.5mm x 200mm)
Plate 1 Pc (6mm x 170mm)
Plate 1 Pc (6mm x 120mm)
Plate 1 Pc (3mm x 100mm)
Two Hole Pipe 1 Pc (φ29 x 40mm)
Chain & Hook 1 Pc
Hex Nut 1 Pc (29mm)

导管一件 (φ22.5mm x L590mm)
锤子一件 (10 Lbs Cast Iron)
导管一件(φ22.5mm x 200mm)
盘子一件(6mm x 170mm)
盘子一件(6mm x 120mm)
盘子一件 (3mm x 100mm)
两孔管一件(φ29 x 40mm)
链条勾一件
六角螺帽一个 (29mm)

NO.KM-1000Y
EXTERNAL PULLER
外经拉拔器
Capacity: 15-80mm
适用范围：15-80mm
NO.KM-1000L1
NO.KM-1000L2
INTERNAL PULLER
内径拉拔器
NO.KM-1000L1 Capacity:15-30mm
NP.KM-1000L2 Capacity:30-80mm
NO.KM-1000L1 适用范围：15-30mm
NP.KM-1000L2 适用范围：30-80mm
NO.KM-1000

INTERNAL & EXTERNAL PULLER SET

內外徑軸承拉拔器
Capacity:
Internal Small 15-30mm
Internal Large 30-80mm
External 15-80mm
适用于：
內徑 15-30mm
內徑 30-80mm
外徑 15-80mm
NO.AT-465

3PC REAR AXLE BEARING PULLER

軸承內徑拉拔器


Capacity:
ID 1"～1-7/8" ,1-3/8"～2-7/8" ,1-5/16"～2-3/8"

适用规格：
1"～1-7/8" ,1-3/8"～2-7/8" ,1-5/16"～2-3/8"
NO.YF-7009
BLIND BEARING PULLER SET
轴承内径拉拔器
Shaft:slide hammer shaft 390 mm long
hammer:weight 100 mm long 2.15Lb.(940g)
spread specification:
8mm: 5/16"-13/32" 8-10 mm
10mm: 13/32"-15/32" 10-12 mm
12mm: 15/32"-9/16" 12-14 mm
15mm: 19/32"-11/16" 15-17 mm
17mm: 11/16"-25/32" 17-20mm
20mm: 25/32"-15/16" 20-24 mm
25mm: 1"--1-1/8" 25-29 mm
30mm: 1-3/16"--1-1/4" 30-32 mm
滑锤杆390毫米长
锤子：100毫米长，重940克
配件适用范围
8mm: 5/16"-13/32" 8-10 mm
10mm: 13/32"-15/32" 10-12 mm
12mm: 15/32"-9/16" 12-14 mm
15mm: 19/32"-11/16" 15-17 mm
17mm: 11/16"-25/32" 17-20mm
20mm: 25/32"-15/16" 20-24 mm
25mm: 1"--1-1/8" 25-29 mm
30mm: 1-3/16"--1-1/4" 30-32 mm
BLIND BEARING PULLER SET
轴承内径拉拔器
One head
hammer: 140 mm long
Shaft:slide hammer shaft 490 mm long
spread specification:
1:17-22mm
2:35-32mm
一个头
锤子：140毫米
滑杆：490毫米
取出器规格：
1:17-22mm
2:35-32mm

Long Jaw Internal Bearing Puller Set

轴承内径拉拔器
Forcing screw (5/8" -1.0P x L180mm SCM415)
Central bolt (7/8" -14T x L60mm SCM415)
Twin head (SCM415)
Leg 2 pieces (SCM415)
Rotated socket 1 piece
Sleeve 1 piece
Extractor: Spread range ψ17-22mm (SCM415)
Extractor: Spread range ψ25-32mm (SCM415)
驱动轴 (5/8" -1.0P x L180mm SCM415)
中轴(7/8" -14T x L60mm SCM415)
双头(SCM415)
支架(SCM415)
旋转套筒一件
取出器：
伸展长度ψ17-22mm (SCM415) ， ψ25-32mm (SCM415)
NO.KM-8081

DIFFERENTIAL SIDE BEARING PULLER

軸承拆裝拉拔器

Spread: 2-3/8" TO 3-3/8"
Reach:1-5/8"
Pressure Screw:
3/4"～16 x 6-11/16"
Adaptor:
1-1/8"～1-1/2"DIA ，1-1/8"～1-5/8"DIA
1-1/2"～1-5/8"DIA 13/16"～1-11/32"DIA

伸展由2-3/8" 到 3-3/8"
可达到1-5/8"
驱动压力3/4"～16 x 6-11/16"
接头
1-1/8"～1-1/2"DIA ，1-1/8"～1-5/8"DIA
1-1/2"～1-5/8"DIA 13/16"～1-11/32"DIA
NO.KM-8085

TRUCK DIFFERENTIAL SIDE BEARING PULLER

軸承拆裝拉拔器

Spread:3-1/2" TO 5-1/2"
Reach: 1-3/4"
Pressure Screw:
3/4"～16 x 6-11/16"s
Adaptor:
1-1/2"～2"DIA , 1-21/32"～2-1/8"DIA
1-27/32"～2-1/2"DIA ,2-3/4"～3-1/16"DIA

伸展由3-1/2" 到 5-1/2"
可达到 1-3/4"
驱动压力
3/4"～16 x 6-11/16"s
接头
1-1/2"～2"DIA , 1-21/32"～2-1/8"DIA
1-27/32"～2-1/2"DIA ,2-3/4"～3-1/16"DIA
NO.KM-960

20PC DIFFERENTICAL SIDE BEARING PULLER

特殊軸承拉拔器

Spread:
3-1/2" TO 5-1/2" , 2-3/8" TO 3-3/8"
Reach:
1-5/8" , 1-3/4"
Pressure Screw:
3/4"～16x6-11/16"

伸展：
3-1/2" TO 5-1/2" , 2-3/8" TO 3-3/8"
可达到：
1-5/8" , 1-3/4"
驱动压力：
3/4"～16x6-11/16"
NO.KM-860

15PC DIFFERENTICAL SIDE BEARING MASTER SET

特殊軸承裝入器

Spread:3-1/2"～5-1/2"
Reach:：1-3/4"
Pressure Screw:3/4"～16 x 6-11/16"
Adaptor:
1-1/8"～1-1/2"DIA ，1-1/8"～1-5/8"DIA
1-1/2"～1-5/8"DIA，13/16"～1-11/32"DIA
1-1/2"～2"DIA， 1-21/32"～2-1/8"DIA
1-27/32"～2-1/2"DIA，2-3/4"～3-11/16"DIA

伸展：3-1/2"～5-1/2"
可达到：1-3/4"
驱动压力：3/4"～16 x 6-11/16"
接头：
1-1/8"～1-1/2"DIA ，1-1/8"～1-5/8"DIA
1-1/2"～1-5/8"DIA，13/16"～1-11/32"DIA
1-1/2"～2"DIA， 1-21/32"～2-1/8"DIA
1-27/32"～2-1/2"DIA，2-3/4"～3-11/16"DIA
NO.KM-8080

AIR CONDITIONER PULLEY PULLER

空調皮帶輪拉拔器

Spread:3" TO 5"
Reach:1-3/8" AND 1-5/8"
Pressure Screw:3/4"～16 x 5"

伸展由3" 到 5"
可达到1-3/8"和1-5/8"
驱动压力：3/4"～16 x 5"
 
 
回页首
UP
  
2005版权所有 京登威国际贸易（天津）有限公司
TEL:86-22-23911572 23911053 FAX:86-22-23924652 EMAIL:13902086782@139.com WEB:http://www.kmastertool.cn