Kingmaster International Trade (Tianjin) Co.,ltd-京登威国际贸易（天津）有限公司
 



 

京登威国际贸易(天津)有限公司
      
KingMaster International Trade(Tian Jin) CO.,LTD
     
其他汽修工具
other tools

GT-A93 ZOOMING FLASHLIGHT 变焦手电

Working voltage ：4.5V continuous lighting hour：〉4H
Alkaline batteries： AAA
LED using hours：100,000 hours
light ：CREE P3 800MM away from the light,（spot light）beginning >=6000LX；after 4H〉=150LX
CREE P4 800MM away from the light,（spot light）beginning light >=6500LX；after 4H〉=150LX
function：instant zooming
switch：self-lock /push switch
WATER PROOF：Can work in the storm
screwed joint：standardized parts
Dimension:104.3*?34.6
weight：<300g

工作电压 ：4.5V 持续照明时间：〉4小时
电池型号：碱性AAA
LED 灯寿命：10万小时
光照度：CREE P3 距光源800MM测试（聚光）初使亮度〉>=6000LX；持续照明4H后〉=150LX
CREE P4 距光源800MM测试（聚光）初使亮度〉>=6500LX；持续照明4H后〉=150LX
功能：瞬间变焦
开关：自锁开关
防水性：暴雨中能正常工作
螺纹连接：标准件
外形尺寸：104.3*直径 34.6
重量：<300g

KM-2114 Combination Electronic Stethoscope Kit 多向电子听诊器组

Engine Stethoscope:
1.Use to locate & identify engine noise
2.Super sensitive microphone pick-up
3.Flexible non-conductive shaft
4.Cushioned headphones
Component Stethoscope:
1.Detect & isolate noisy componets
2.Enables road test diagnosis
3.6 channel sensor selector unit
4.6 pick up sensors -4.8m long cords

发动机听诊器：
1.定位并确定发动机噪音。
2.超敏感话筒拾音器
3.非传导性软轴
4.带衬垫的耳机。

听诊器组件：
1.用于检测并隔离噪音的组件。
2.用于路上检测。
3.6个频道的传感器选择器.
4.6个传感器拾音器，带有4.8米长的电线

KM-2118 Engine Mechanic's Stethoscopeset 电子听诊器组
Engine Stethoscope:
1.Use to locate & identify engine noise
2.Flexible non-conductive shaft
3.Cushioned headphones 		发动机听诊器：
1.定位并确定发动机噪音。
2.非传导性软轴
3.带衬垫的耳机。
KM-300 Compressed Air Water Remover 空气滤清器（除水、油）

Max. opereation flow rate :800 NI/min
Operating pressure range : 0.1-0.93Mpa(1.0-9.5kg/cm2)
Max pressure before failure: 1.5 Mpa (15.3kg/cm2)
Fluid temperature :5-60℃
Drain outlet connection diameter: 1/4 Rc
Air line connection diameter:3/4 Rc
Weight:2.3kg

最大可耐压力：140kg/cm(2000psi)
安全操作压力：1-70kg/cm(1-1000psi)
气体温度：6-65℃
排水方式：自动泄压阀
进出气口径：3/4"
排水口:1/8"
尺寸（长x外径）：482x115mm
重量（净重）：2.7Kgs

 

KM-300-1 Compressed Air Water Remover 空气滤清器（除水、油）
Max. opereation flow rate :800 NI/min
Operating pressure range : 0.1-0.93Mpa(1.0-9.5kg/cm2)
Max pressure before failure: 1.5 Mpa (15.3kg/cm2)
Fluid temperature :5-60℃
Drain outlet connection diameter: 1/4 Rc
Air line connection diameter:3/4 Rc
Weight:2.3kg

最大可耐压力：140kg/cm(2000psi)
安全操作压力：1-70kg/cm(1-1000psi)
气体温度：6-65℃
排水方式：自动泄压阀
进出气口径：3/4"
排水口:1/8"
尺寸（长x外径）：482x115mm
重量（净重）：2.7Kgs

 

Diesel Injection Socket

剖沟套筒

3/8" DR. Diesel injection socket

CR-V 22 mm MAT finish

3/8" DR.剖沟套筒
NO.KM-0100

Dynamo LED torch

手摇充电电筒

Specifications:
1.LED: 3 - 4V
2.Free of Carbon-Zinc battery NI-MH battery
3.ELead-Acid or NI-MH battery flashlight
(money-saving & environmenvironmentally friendly vanguard
Description:
1.Super bright LEDs(15,000 MCD)
2.Generate power anywhere anytime without power source.
3.Free of Carbon-Zinc, ntally friendly)
4.Emergency helper against disasters - earthquake, typhoon,
power failure.......
5.Good for housework, maintenance, travelling,
mountain-climbing & more......
PRODUCT SIZE:
13.9 x 5.3 x 5.2cm

规格：
1.发光二极管：3-4 伏
2.无需传统电池.
3.绿色环保。
描述：
1.发光二极管高强光(15,000 MCD)
2.在任何没有交流电源的情况下，可自行产生电流.
3.无需传统电池的手电筒，省钱且保护环境,
4.灾难情况下，如地震，台风，停电时的好光源.
5.适用于家居，旅行，登山.......

产品尺寸：
13.9 x 5.3 x 5.2cm
NO：KM-37F

3PCS FLEXIBLE PLIERS SET
三件可弯曲钳子组

A flexible combination plier NO.KM-7LPF
B flexible cutter plier NO.KM-7CPF
C flexible neddle nose plier NO.KM-7NPF
D 3PCS FLEXIBLE PLIERS SET NO.KM-37F

可弯曲钳子组单件及组合:
特征: 180度内可调节任意角度,操作角度灵活,应用更广泛.
 
NO.KM-6355
EXHAUST SPRING CLAMP REMOVER/INSTALLER
排气管C型夹拆装器
Essential for safe,controlled removal of clamps attaching
exhaust to manifold.
Special disign provides "leverage"required to expand
the spring clamps
Volkswagen
安全，易操作的排气管夹拆卸必备工具，
特殊杠杆设计，可拆卸力量强大的排气管弹簧夹.
适用于大众系列汽车
NO:KM-62109
NORTRSTAR WATER PUMP SOCKET
冷却水泵浦套简
1 Used to remove and install the water pump on
cadillac Northstar 4.6 liter v-8 engines 1993
and later and oldsmobile Auraro 4.0 liter v-8
engines 1997 and later.
2 Enhanced duralibility
3 More strength and control in removing and
replacing water pump impeller

1 用于取出及安装水泵，适用于卡迪拉克北极星4.6升V－8引擎1993 及改进引擎,
以及AURORA4.0升V-8引擎1997及改进引擎

2 坚固耐用

3取出或装入水泵叶轮时更省力，易操作.
NO.AGG-8
360°ANGLE-FREE AIR GREASE GUN
自动连续可变角度黄油枪
360° Angle-Free rotating selected to meet confine space for active, quick and labor-saving operation

Special AIR MOTOR design keep incessantly and automatically priming
枪头可以做360度旋转，适合任何操着空间，特殊设计，可连续不间断自动喷灌。
NO.SE-6A
6PCS SCREW EXTRATOR SET
6件断头螺丝取出器
Specification:
N0．1 3—6
N0．2 6—8
N0．3 8—10
N0．4 10—14
N0．5 14—18
N0．6 18—24
螺丝取出器规格 相应的螺栓规格
N0．1 3—6
N0．2 6—8
N0．3 8—10
N0．4 10—14
N0．5 14—18
N0．6 18—24
 
Fuel Injection Test Kit
燃油压力表

contains:
Many adaptors and necessary fitting for checking the fuel injection systems on most domestic and foregin cars.
Feature:
1)A large 3-1/2"gause with dual readings of 0-145 PSI and 0-1000 KPA; It also has a 2-1/2" low pressure gauge for an accurate reading below 15 PSI
2)All adaptor gauge and hose assemblies feature a quick coupling system for speedy and efficient connection testing
3)The relief valve is unique in that it relieves the pressure and the fuel safely; it also allows you to check for sufficient fuel flow
4)No need for wrenches or pipe dope
5)The plastic blow molded case is designed for compact neat storage
6)Complete with instruction manual

包含有：
检测大多数国产车及进口车燃油压力系统的转换接头及相关配件

特征：
1）3-1/2"显示表盘0-145 PSI 及0-1000 KPA ;2-1/2"精确小表盘可读低于 15 PSI 数值。
2）所有接头及联接管在快速检测中表现出色
3）独特安全阀能更安全地解除燃油压力，也可检测燃油的流动。
4）无需扳手及连接管润滑料
5）塑料吹气盒设计更适合存储。
6）随附操着手册
 
Unique Compression Tester Kit
汽缸压力表

1)Easy-reading 2-1/2" diameter gaugecalibrations with 0-300 PSI 20kg/cm,20 bar
2)13"durable rubber hose with 14 mm /18 mm adapter
3）6" heavy-duty stem with universal rubber cone adapter fits all plug holes.

1)2-1/2"表盘可读 0-300 PSI 20 bar 20kg/cm*cm
2)13"橡胶管，14mm/18mm 转接头
3）6"杆适合大多数插口。
 
9 pcs"T" Handle Nut Driver
9件"T"型螺帽起子
size:5 6 7 8 9 10 11 12 13 mm
规格: 5 6 7 8 9 10 11 12 13 mm
 
11 pcs Nut Driver
11件螺帽起子
Size: 4 5 5.5 6 7 8 9 10 11 12 13 mm
规格: 4 5 5.5 6 7 8 9 10 11 12 13 mm
KM-641
KM-640A
1/2"DR.Window Type Micro Torque Wrench
1/2"方视窗型扭力扳手
Range:
KM-641---10KG
KM-640A--20KG
适用扭力范围：
KM-641---10KG
KM-640A--20KG
 
TORQUE WRENCH
扭力扳手

NO. ARD80 1/2" DR.100NM
NO. ARD80 3/8"DR. 100NM
NO. ARD150 1/2" DR.210NM
NO. ARD250 1/2" DR.350NM
NO. ATW10 3/8" DR.10M/KG
NO. ATW20 1/2" DR.20M/KG
NO. ATW35 1/2" DR.35M/KG
NO. ATW42 3/4" DR. 42.8M/KG(420NM)
NO. ATW50 3/4" DR.50-300FT-LB(NM-560)
NO. ATW70 3/4" DR.100-500FT-LB(NM-700)
NO. ATW100 3/4" DR.(OR1")100-700FT-LB(NM-980)
NO.GOW-7
7 PCS GEAR TYPE OFFSET WRENCH
7件齒輪式雙梅花扳手
10x11, 12x14, 15x16, 13x17, 19x22, 24x27, 30x32
Each head is reversible with a bolt which can change working direction.
產品功能與特性:

工业极产品


為強力形型之梅開扳手,且兩頭都有推杆,可任易
切換使用方向。
KM-B19001WS

CORDLESS IMPACT WRENCH
充电冲击扳手

SPECIFICATION
Battery: DC 19.2v panasonic 2000 mAh Ni-Mh
No-load speed(RPM) 0~2500rpm ±10%
Switch form:Turn right /left ,step less ,brake
Driver chank: 1/2”
Weight(with battery) 2.943kg
Size: 253*78*204(mm)
Size with battery pack 253*80*260(mm)
Max Torque
Kgf-cm 3365±10%
Lb-ft 243.4±10%
N-m 330±10%
No-load current 2.8 4.2 A
Standard packing: plastic carring case.
DETAILS REFER TO THE ATTATHED HANDBOOK

规格
电池: DC 19.2v panasonic 2000 mAh Ni-Mh
空转速度: 0~2500rpm ±10%
转动方向:右/左 减速 停止
驱动器规格： 1/2”DR
含电池重量 2.943kg
尺寸 253*78*204(mm)含电池盖尺寸253*80*260(mm)
最大力矩
Kgf-cm 3365±10%
Lb-ft 243.4±10%
N-m 330±10%
空转电流 2.8 4.2 A
包装:可提走塑料盒
详情参见盒内附手册.
No.GP-234
No.GP-237
2&3 Jaws 2In1 Gear Puller
两爪三爪轴承拔

Drop forged chrome vanadium steel
4"102mm Capacity Range 3"-4"
7"178mm Capacity Range 3"-7"
铬钒钢锻造
4"120毫米适用范围3"－4"
7"178毫米适用范围3"－7"

Operate Instruction:
1.You can operate this product with 3 jaws or 2 jaws pulling.even two different pulling ways:External or Internal models,only need to change or convert jaws sddembling.
2 How to change or convert jaws assembing: please relax the Round screw cap in order to relax the pressure spring, then you can easy to move the jaws from the central cross arm.
3 When you operate this product please make sure all parts are fixes on the right place,even all the accessories without any damage.
4 After operating,please maintain all parts and often to keep all the accessories clean.
操做说明：
1 该工具在可用做内外径拉拔器的同时，还可作为3爪和2爪拉拔器，只需更换拉拔爪手即可.
2 更换拉拔爪手方法：先旋转松懈圆头螺帽，以解弹簧压力，然后可轻易从中央臂上拆除拉拔爪手.
3 操着此工具时，请务必保证所有零部件都被固定在正确的位置，任何零部件不许有任何损坏,
4 使用之后请收好各部件，并保证所有零部件清洁.
 
Long Jaw Internal Bearing Puller Set
長瓜型内径轴承拉拔器
Forcing screw (5/8" -1.0P x L180mm SCM415)
Central bolt (7/8" -14T x L60mm SCM415)
Twin head (SCM415)
Leg 2 pieces (SCM415)
Rotated socket 1 piece
Sleeve 1 piece
Extractor: Spread range ψ17-22mm (SCM415)
Extractor: Spread range ψ25-32mm (SCM415)
驱动轴 (5/8" -1.0P x L180mm SCM415)
中轴(7/8" -14T x L60mm SCM415)
双头(SCM415)
支腿(SCM415)
旋转套筒一件
取出器：
伸展长度ψ17-22mm (SCM415) ， ψ25-32mm (SCM415)
 
BLIND BEARING PULLER SET
内径轴承拉拔器
One head
hammer: 140 mm long
Shaft:slide hammer shaft 490 mm long
spread specification:
1:17-22mm
2:35-32mm
一个头
锤子：140毫米
滑杆：490毫米
取出器规格：
1:17-22mm
2:35-32mm
NO.KM-62111
3PCS OIL FILITER GAP WRENCH SET
3件滤油心上盖拆卸组(欧式)
(1) 3/8" SQUARE DRIVE MANUFACTURED FROM CHROME VANADIUM STEEL
(2) SIZE: 27m/m MERCEDES: A CLASS
(3) SIZE: 32m/m VAUXHALL/QPEL: ASTRA,CORSA,ZATIRA.
(4) SIZE 36m/m
VAUXHALL/OPEL: OMEGA DL 16V VECTRA,ZAFIRA>98
BMW: 16VFORD: MONDEO 2.0D 16V DURA TORQ ENGINE,
TRANSIT 2.5 & 2.0 DURA TORQ DIESEL ENGINE.
MERCEDES: 116MB ENGINE VITO CDI
A: 适用于10 mm 汽门螺栓的所有车型
B: 适用于12 mm 汽门螺栓的所有车型
C: 适用于 9/16"汽门螺栓的所有车型
D: 优先使用于“大众”和“保时捷”13 mm 汽门螺栓
 
Tie Rod/Pitman Arm Adjusting Set
连杆臂调节工具组
these tools have a unique design that permits 360 °rotation of
the adjusting sleeve,even where space is limited.
Accommodate 1/2"drive ratchet or breaker bar.
该产品设计独特，在较小空间亦可执行调整之功能，可360度旋转。
与1/2“棘轮扳手配套使用
7886
12 PCS A/C COMPRESSOR CLUTCH REMOVER KIT
12件空调压缩机离合器拆卸组

Replaces clutches found on FS6,C171,6P & 148 compressor,
GM R4 & A6,DA-6 &V5 A/C compressor,sanden compressors
SD505,507,510,575,708, & 709 2 & 3 hole puller plate fits
most clutches， mechanical force does the pulling
Blow molded case for easy storage and transport
Case dimensions:(L)9"×(W)8"×(H)2"
Net Weight:1.36kg
可拆卸以下空调压缩机离合器
FS6,C171,6P & 148 压缩机,GM R4 & A6,DA-6 &V5
空调压缩机 SD505,507,510,575,708, & 709
2,3孔拉拔盘适用于大多数离合器，机械力拉拔
吹气盒便于存放和携带，
盒子规格 (L)9"×(W)8"×(H)2"
净重1.36kg
7847
Power Steering Pump Pulley Kit
五件动力方向盘皮带轮拆装器
works on ford,GM,& Chrysler vehicles with saginaw
Fits 1-1/8",1-1/4".1-5/16",1-3/8"pulley Hub Dia.
Including 1988 to current GM cars equipped with Quad 4 engines,
1991 to current GM mini vans with 3.1L and 2800 v-6 engines,1991
to current Ford 4.6L engines with a metric shaft.
Includes spacer for power steering pump pulley installation on
Chrysler irrus/jstratus /Breeze
适用于福特，通用，克莱斯勒机车
适用于1-1/8",1-1/4".1-5/16",1-3/8"皮带轮，包括以下机车：
通用Quad 4引擎1988至今机车
通用迷你3.1升2800 V-6引擎1991至今机车
福特4.6升1991至今机车
NO:KM-6257

VALVE REFACING AND SEATING TOOLS
气门座绞刀

Precision machined tungsten carbide blades produce
valve seats with: accurate seat angle ,superior seat surface true,
flat seal seats concentric with valve guide.
Available in a wide range of cutter diameters and angles.
Contents: CUTTER 52mm-65mm 75°AND60°
46mm-60mm 45°AND30°
44mm-52mm 75°AND30°
37mm-46mm 68°AND45°
37mm-44mm 75°AND30°
28mm-35mm 75°AND45°
5 pcs expandable pilot 5.5mm-12.5mm “T ”wrench handle

钨钢刀片的精确气门座绞刀修整气门座有以下特点：
角度更精确,座面更优质,封条更平滑,同心座有气门导管
组件：绞刀 52mm-65mm 75°AND60°
46mm-60mm 45°AND30°
44mm-52mm 75°AND30°
37mm-46mm 68°AND45°
37mm-44mm 75°AND30°
28mm-35mm 75°AND45°
5件可张开杆,T型扳手柄
可提供各种规格（直径，角度）的绞刀
NO.KM-6335B
5PCS DRIVER NUT SET
五件避震弹簧螺帽组
NO.1: 10.5MM VW GOLF REAR AXLE
NO.2: 12.5MM VW POLO FRONT AXLE
NO.3: 14.5MM POLO, GOLF, PASSAT AUDI 80
NO.4: 14.5MM AUSTIN MAESTRO
NO.5: 14 MM BENZ (W203)
适用车型
NO.1: 10.5MM 大众 高尔夫 后轴
NO.2: 12.5MM 大众 POLO 前轴
NO.3: 14.5MM POLO 高尔夫 帕沙特 奥迪80
NO.4: 14.5MM 奥斯丁(英制轿车)
NO.5: 14 MM 奔驰（W203)
KM-6357A
(KL-0005)
UNIVERSAL SPRING COMPRESSOR
避震弹簧压缩器
For use with all macpherson struts in which spring
pcessure does not exeed 8 000 N.
Max.load : 8 000 N Compression length: 65-320mm
Accessories: 1 pair of spindles for self-levelling
spring assemblies
适用于弹簧压力8 000牛顿以内
最大负荷： 8 000牛顿
可调节长度： 65－320mm
配件：一副弹簧测量杆
NO:KM-04430

42PCS 1/2"DR.SPHERICAL SOCKET SET
42件1/2"方球型套筒组

1-pc 1/2"dr. 72 teeth ergonomic quick release ratchet handle
1-pc 1/2"dr.extension bar 125mm
1-pc dr. extention T- bar 250mm
17-pcs 1/2" dr.spherical sockets10,11,12,13,14,15,16,17,
18,19,20,21,22,24,27,30,32mm
1-pc 1/2"dr.universal joint
1-pc 1/2" bit adapter*10mm
8pcs 10*30mm Tor* bits T20,25,27,30,40,45,50,55
6pcs 10*30mm Hex bits 5,6,7,8,10,12mm
6pcs 10*30mm XZN bits M5,6,7,8,10,12mm
组件：
1件1/2英寸72齿快速脱落棘轮扳手
1件1/2英寸连接杆125mm
1件T型接杆250mm
17件1/2英寸特殊球型套筒10,11,12,13,14,15,16,
17,18,19,20,21,22,24,27,30,32mm
1件1/2英寸万向接头
1件1/2英寸转接头10mm
8件10×30mm六角星型套筒头T20,25,27,30,40,45,50,55
6件10×30mm六角套筒头 5,6,7,8,10,12mm
6件10×30mm XZN 套筒头 M5,6,7,8,10,12mm


The spherical socket can work on 6 kinds of nuts due to its special design.（left photo shows）

球型套筒特殊设计，适用六种螺帽 （如左图）
NO:KM-31340
40PC 3/8"DR.GO-THRU SPHERICAL SOCKET SET
40件3/8"方球型通心套筒组

CONTENT:
1-pc 3/8"dr.Go-Thru 72 teeth ratchet handle
1-pc 3/8"dr.extension bar 150mm-Go-thru type
1-pc 3/8"dr.extention bar 75mm-Go-thru type
14-pcs 3/8" dr.Go-thru spherical sockets8,9,10,11,
12,13,14,15,16,17,18,19,21,22mm
1-pc 1/2"dr.adapter
1-pc 1/4"adapter
1-pc 1/4:dr.bit adapter
1-pc 10mm bit adapter
8pcs 10*30mm Torx bits T20,25,27,30,40,45,50,55
6pcs 10-30mm Hex bits 5,6,7,8,10,12mm
5pcs 10*30mm XZN bits M5,6,8,10,12
组件：
1件3/8”通心72齿棘轮扳手
2件3/8”通心连接杆150mm 75mm
14件3/8”特殊通心套筒8,9,10,11,12,13,14,
15,16,17,18,19,21,22mm
2件套筒转换接头1/2”和1/4”
2件套筒头转换接头1/4”和10mm
8件10×30mm六角星型套筒头T20,25,27,30,40,45,50,55
6件10×30mm六角头5,6,7,8,10,12mm
5件10×30mm XZN型套筒头M5,6,8,10,12


The spherical socket can work on 6 kinds of nuts due to its special design.（left photo shows）
球型套筒特殊设计，适用六种螺帽 （如左图）
NO.KM-62134
PULLERS FOR AUDI/VW CAM WHEELS
正时飞轮拆装组

With 4 special -purpose claws
For pulling spoke-type cam wheels on TDI4-,6- and 8-cylinder
dieselengines and on V6,V8 gasoline engines from 1998 on.
The scope of supply includes 4 claws
适用于奥迪，大众各车型
4支特制爪，可取幅式凸轮齿轮
适用1998年后的四，六，八，缸
柴油机引擎和V6，V8汽油机引擎
NO.KM-62124
(T40030)
CAM HOLDING FIXTURE
引擎曲轴固定组
Used to align and hold
camshaft,applicable:
Audi 3.0L V6 5-valve.
用于连接并固定凸轮轴，
适用于奥迪3.0升V6五气门。
NO.KM-7105
CRANKSHAFT LOCKING TOOL(VOLKSWAGEN)
时规皮带固定器(适用于大众汽车)
For use on Volkswagen ,
BORA, GOLF,LUPO & POLO TDI'S
适用于大众汽车系列
宝来，高尔夫，LUPO & POLO TDI'S
NO:KM-6297B
8PC5 TIMING LOCKING TOOL KIT
8件正时皮带固定器组
A: VAUXHALL/OPEL 欧宝
ASTRA G 1.7 TD
ASTRA-G 2.0 16V
VECTRA 1.8/2.0 16V<95
B: VAUXHALL/OPEL 欧宝
ASTRA G1.4/1.6/1.8 16V<94
VECTRA 1.6/1.8 16V
ZAFRIA 1.6/1.8 16V
C&D:
RIGHT HAND CAMSHAFT右凸轮轴
SAAM900 X 9000
VAUXHALL/OPEL 欧宝
CALIBRA 2.6/2.51/2.6 V6
CAVALIER 2.51 V6
OMEGA-B欧米迦 2.5/2.61/3.0/3.2 V6
SINTRA 3.0 V6
VECTRA-A 2.5/12.51/2.6 V6
LEFT HAND CAMSHAFT 左凸轮轴
E:
ROVER: 25 1.4/1.6/1.8/VVC.45
1.4/1.6/1.8 75 1.8. 200 VI.214 16V
216 16V/CABRIO/COUPE
218 COUPE. 414 16V " 418 16V/TOURER
BRM 1.8VVC . METRO GTI/GTA 16V
MGF 1.8VVC. MOST MODELS
F:
VOLKSWAGEN: BORA 1.9TDI GOLF 1.9
TDI.LUPO 1.2/1.4/3.0 TDI. POLO 1.4
TDI PASSAT 1.9 TDI
适用车型大众系列，宝莱1.9TDI,
高尔夫1.9 TDI,LUPO 1.2/1.4/3.0 TDI
POLO 1.4TDI,帕撒特1.9 TDI.
G:
CITROEN:BELLINGLE 1.9D. DISPATHCH 1.9D/TD. FSO 1.9D
RELAY 1.9D/TD. SYNERGIE 1.9/2.OT.RANTIA 1.9/2.0 D/TD
XASRA 1.9/2.0 D/HDI. ZX 1.9D/TD.MOST MODELS
FIAT菲亚特DUCATO 2.OD,ULYSSE 1.8/2.O TURBO
FORD: MOST MODELS 福特大多数车型
PEUGEOT :205. 1.6/1.8/1.9D. 306 1.8/1.9D/TD 309 1.6/1.9 405 1.6
/1.9D.406 1.9D. 605 2.0 D/TD 806 1.9TD. BOXER 1.9/2.0 D/TD.EXPERT 1.9D
TALBOT: EXPRESS D .HORIZON D.J5 D.SOLARA
H:ISUZU:1.5/1.7 DIESEL ENGINES
五十铃：1.5、1.7 柴油机引擎
VAVXHALL/OPEL欧宝:
1.6/1.7 DIESEL ENGINES 柴油机引擎1.2/1.4/1.6/1.8/2.0
OHC PETROL ENGINES (OHC 汽油机引擎)
 
 
回页首
UP
  
2005版权所有 京登威国际贸易（天津）有限公司
TEL:86-22-23911572 23911053 FAX:86-22-23924652 EMAIL:13902086782@139.com WEB:http://www.kmastertool.cn